My A&R · Studio Builder
Build my vocal chain
Tell us your DAW, interface, mic and the plugins you use. You'll get exact starting settings for every plugin, a gain-staging walkthrough, step-by-step instructions to build the template in your DAW, and a routine for using it every session.
Your studio
Creative vocal profile 10
Southern Soul & Blues Warmth
Full-bodied, soulful, warm lead vocals that sit naturally over a live-band groove.
Style references: King George, Tucka, J-Wonn, Sir Charles Jones. Style references describe a general sound direction only. My A&R is not affiliated with or endorsed by these artists, and presets do not recreate anyone's voice or recordings. Your performance and identity stay central.
Effect rack (each on its own 100% wet return; untick to bypass)
Background vocals: Gospel-style harmony layers and call-and-response, warm and slightly behind the lead.
Ad-libs: Melodic ad-libs between lines, plate-heavy.
Verse: Conversational and present.
Chorus: Call-and-response backgrounds up, more plate.
Creative options
- Gospel-style harmony layers
- Vocal call-and-response
- Tasteful vibrato preservation
- Melodic ad-libs
Calibration rules
- Identify the song's actual key and scale before enabling automatic pitch correction.
- Use the vocal-range setting that matches the singer when tracking.
- Leave sensible headroom and avoid clipping. Don't force files to an arbitrary LUFS value.
- Adjust compressor thresholds and input levels until you see the stated gain reduction; the numbers are targets, not knob positions.
- EQ moves are conditional: don't boost or cut a frequency unless the recording benefits.
- Put reverbs, delays and doublers on separate aux returns set to 100% wet, and set return levels by listening in context.
- Keep the original unprocessed recording. Process copies or use non-destructive inserts.
Before you call it done: preset QA
- Tested on more than one voice type and microphone
- No unintended clipping, harshness, pumping or excess sibilance
- Processed vs unprocessed compared at matched loudness
- Checked in stereo and mono
- Tested on a verse, a chorus and a louder performance
- Latency and CPU checked (raise buffer when mixing)
- Plugin names and parameters validated against the My A&R plugin database
Start here
Gain staging: the most important step
Every setting in your chain assumes the vocal arrives at a healthy, consistent level. Get this right and the plugins behave as described; get it wrong and no setting will sound right.
1. Know the target numbers
- While recording: normal singing averages about -18 dBFS; the loudest words peak around -10 to -6 dBFS.
- Nothing should ever hit 0 dBFS. Digital clipping can't be repaired.
- Why -18 dBFS: most analog-modelled plugins (1176, LA-2A, Pultec, channel strips) are calibrated so -18 dBFS equals their sweet spot (0 VU). Feeding them hotter makes them distort and over-compress.
2. Set the preamp on your Universal Audio Apollo (Twin/x)
- In the UAD Console app, set the preamp gain on the input (or on the Unison preamp plugin if you use one). Watch Console's input meter, not just the DAW.
- Have the artist perform the LOUDEST part of the song (the hook or the ad-lib shouts), not the quiet verse, and set gain for that.
- Then record a 10-second test and check the DAW meter matches the targets above.
3. Even out takes with clip gain BEFORE plugins
- In Pro Tools, use Clip Gain (show it with View > Clip > Clip Gain Line, or use the clip-gain fader on each clip).
- Turn up quiet words and phrases and turn down shouted ones so the whole vocal sits within a few dB. This is what top engineers do first; it makes the compressors work gently instead of fighting.
- Pro Tools meters show peaks; aim the loudest phrases at the yellow zone, never red.
4. Trim into the chain
- Put Trim (Plug-in > Other > Trim) as the very first insert. Adjust it so the vocal averages about -18 dBFS going into the first plugin.
5. Level-match every plugin
- After setting each plugin, toggle bypass on and off. The loudness should stay the same; only the tone or dynamics should change.
- Use each plugin's Output/Gain/Make Up control to match. Louder always sounds "better", so this is the only fair way to judge a setting.
6. Keep the faders honest
- Set the balance with clip gain and trim so faders sit near 0 dB (unity), where they have the finest control for rides.
- Leave the mix bus peaking around -6 to -3 dBFS. If it's hotter, pull down all tracks (select all and lower together), not the master fader.
- Gain: expect about 25–45 dB of preamp gain for the Other condenser (e.g. ECM-87). Set it so the loudest phrases peak around -10 to -6 dBFS and normal singing averages near -18 dBFS. Leave headroom; you can't fix clipping later.
- Your Universal Audio Apollo (Twin/x) (about 65 dB max gain) has enough gain for this mic.
- Distance: 6–10 inches (15–25 cm) with a pop filter; angle slightly off-axis if sibilance is strong. Condensers pick up the room, so treat behind the singer.
- Treated room: keep the same mic position between sessions so takes match.
- Apollo Unison: if you own a Unison preamp plugin (610, Neve, API), insert it on the input and set gain there. Print through at most a light compressor (2–3 dB GR) or track clean; you can always add more later.
- Record at 24-bit, 48 kHz (or 44.1 kHz if the project already uses it). Record 3–5 full takes plus punch-ins for comping.
Your chain with exact starting settings
Signal flow
Sends from the vocal track: Reverb (D-Verb) · Delay (Mod Delay III)
Vocal inserts, in order
1Corrective EQ
EQ3 7-Band · Avid · insert
HPF Freq 80 Hz, 12–18 dB/oct (profile range 70–85 Hz)Clears rumble and plosive thumps below the voice. Band Freq 270 Hz (investigate 220–320 Hz)Boxiness/mud region for this voice and room. Only cut if you hear it. Band Gain -1 to -2 dB What it does: Removes what you don't want before anything is compressed: rumble, plosive thumps and boxy build-up.
Check: Solo the vocal and sweep the cut: it should sound clearer, not thinner. Bypass to compare.
2Compressor 1: fast peak control
Dyn3 Compressor/Limiter · Avid · insert
Threshold Set for 2–4 dB GR Ratio 4:1 Attack 8–15 ms Release 60–100 ms Knee Medium/soft Gain Match the bypassed level What it does: Catches the loudest words fast so the vocal stays in front without jumping out.
Check: Gain reduction should move with the words and return to near 0 between phrases.
If: If consonants get dull, slow the attack a step.
If: If GR never returns to 0, the release is too slow or threshold too low.
3Compressor 2: smooth leveling
Dyn3 Compressor/Limiter · Avid · insert
Threshold Set for 1–3 dB LA-2A-style GR Ratio 2:1–3:1 Attack 20–30 ms Release 120–200 ms (or Auto) Knee Soft Gain Match the bypassed level What it does: A slower, gentler second stage that evens out the whole performance.
Check: Works as a second stage: steady 2–3 dB GR that evens out the performance without pumping.
4De-esser
Dyn3 De-Esser · Avid · insert
Frequency 6500 Hz (sweep ±1 kHz to find the "s") Range 1–3 dB What it does: Turns down only harsh "s", "sh" and "t" sounds, which compression and brightness make worse.
Check: Only the "s", "sh" and "t" sounds should trigger reduction; normal words must not lisp.
5Tone EQ
EQ3 7-Band · Avid · insert
HPF Freq Gentle 2–4 kHz if needed Band Gain Middle of the range What it does: Shapes the character: presence for clarity and air for openness, only where the recording benefits.
Check: The vocal should cut through the beat at the same fader level without sounding harsh. If it gets harsh, check the de-esser before reducing the boost.
Sends
1Reverb (send)
D-Verb · Avid · send
Algorithm Plate or chamber Pre-Delay 30–50 ms Size 1.3–1.9 s HF Cut 6–8 kHz Mix 100% wet (it is on a send) What it does: Places the vocal in a space. On a send so you control how much, and it never muddies the dry signal.
Check: Send the vocal at about -18 dB. High-pass the reverb return at 250–300 Hz. You should notice it when muted more than when playing.
If: If the vocal sounds far away, shorten the decay or lengthen the pre-delay.
2Delay (send)
Mod Delay III · Avid · send
Delay Slapback 100–125 ms mono (not tempo-synced) Feedback 0–10% LPF 4–5 kHz Mix 100% wet (send) What it does: Echoes timed to the song for width and depth without washing the vocal out like long reverb can.
Check: Send at about -20 dB for space, and automate louder "throws" on the last word of key lines.
Bus
1Vocal bus glue
Dyn3 Compressor/Limiter · Avid · bus
Ratio 2:1 Attack 30 ms Release Auto or 150–250 ms Threshold 1–2 dB GR on the vocal bus Gain Match level What it does: Glues lead, doubles and ad-libs together so they sound like one performance.
Check: Route lead, doubles and ad-libs to one vocal bus; this glues them without squashing.
Mix bus precautions
- Keep the mix bus peaking around -6 to -3 dBFS with no limiter when sending to mastering.
- If you mix into a limiter for a loud preview, set its ceiling to -1 dBTP and keep gain reduction under 3 dB, then remove it for the final premaster.
- Check the mix in mono and on earbuds/phone before bouncing. Bounce 24-bit WAV at the session rate.
- Typical Southern Soul vocal level: 2 to 6 LU relative to the beat. Grade your bounce in Mix Lab to confirm.
- Saturation: no matching plugin in your list.
- Saturation: no saturation plugin in your list; a tape or tube plugin at low drive would add warmth.
- Pitch: Southern Soul & Blues Warmth usually leaves tuning off or does it by hand; use automatic correction only gently (Usually off, manual, or 35–60 ms).
Plugin database 2026.11.2. Values are starting points chosen for your gear, voice, room and style; confirm each with its check. Not affiliated with any plugin maker; names are trademarks of their owners.